juhendid | seadistused | veateAted
Vali siit soovitud NORDCEL seadme tooteseeria, et näha paigaldusjuhendeid ja veakoodide kirjeldusi
+8°C = soojuspumba funktsiooni käivitamiseks vajutage kütterežiimis olles samaaegselt nuppe TEMP + CLOCK.
Puldi ekraanile kuvatakse sümbol ja valitud temperatuur +8°C. Funktsioonist väljumiseks korrake protseduur
Puldi ekraanile kuvatakse sümbol ja valitud temperatuur +8°C. Funktsioonist väljumiseks korrake protseduur
NORDCEL NF-seeria (R32) NF21-25DCL | NF21-35DCL | NF21-50DCL | NF21-71DCL
|
|
WiFi app seadistamine:
| ||||||||||||||||||||||
NORDCEL NS21-Seeria (r32) NS21-25G10L | NS21-35G10L | NS21-50G10L
|
| ||||||||||||
WiFi seadistamine
2. Registreeruge rakendusele, valides kasutajanimi, parool ja sisestades oma e-posti aadressi ja Euroopa piirkonna.
3. Vajutage nuppu "+", et lisada soojuspump oma seadetesse.
4. Valige ja vajutage AC ikoonile
5. Järgmisel ekraanil valige "Kaugjuhtimispult (ilma wifi nuputa)
6. Vajutage puldi juhtnuppe TURBO ja MODE samal ajal ja umbes 10", kuni piiks kõlab ja ikoon "Wifi" puldi ekraanil on aktiveeritud.
Nii saavutatakse wifi-mooduli RESET.
Sellest hetkest alates on meil protsessi lõpuleviimiseks 2-minutiline ajaaken, vastasel juhul tuleks seda protsessi korrata alates 5. sammust.
Nii saavutatakse wifi-mooduli RESET.
Sellest hetkest alates on meil protsessi lõpuleviimiseks 2-minutiline ajaaken, vastasel juhul tuleks seda protsessi korrata alates 5. sammust.
7. Järgmisena vajutage nuppu JÄRGMINE rakenduse ekraanil
8. Sisestage selle piirkonna WiFi-võrgu parool, kuhu soojuspump on paigaldatud, ja vajutage otsinguseadet.
9. Rakendus otsib seadet ja loob automaatselt ühenduse GREE Cloudiga. Seejärel kuvatakse järgmine ekraan.
10. Ilmuval ekraanil vajutage OK ja meie seade on nüüd ühendatud.
Lisainfot funktsioonide kohta leiate siit allpool olevast lingist
Lisainfot funktsioonide kohta leiate siit allpool olevast lingist
| ||||
Nordcel NC20-seeria (R32): NC20-25G10L | NC20-35G10L | NC20-50G10L
|
|
| ||||
NORDCEL NA19-seeria (R32): Na19-25G10L | NA19-35G10L | NA19-50G10L | NA20-70G10L
|
8 °C küttefunktsiooni käivitamiseks vajutage kütterežiimis olles samaaegselt nuppe TEMP ja CLOCK.
Puldi ekraanile kuvatakse sümbol ja valitud temperatuur 8 °C. Funktsioonist väljumiseks korrake protseduur Refrigerant recovery function:
Külmutusagensi kokkukogumise funktsioon: 5 minuti jooksul pärast seadme vooluvõrku lülitamist (seadme ON või OFF olek on selleks sobiv) vajutage 3 sekundi jooksul järjest "LIGHT" nuppu 3-korda, et käivitada külmutusagensi kokku kogumise režiim; Siseosa ekraanile kuvatakse "Fo" ja funktsioon käivitub. | ||||||||||
|
NA19-50G10L ja NA19-70G10L seadmetel on min. ühendustoru pikkus 3m
Maks. ühendustoru pikkus ja max. suur erinevus. (Lisateavet vaadake spetsifikatsioonidest.) Täiendav külmutusagensi õli ja külmutusagensi laadimine, mis on vajalikud pärast ühendustoru pikendamist
|
Täiendava külmaaine (R32) lisamise tabel
|
NORDCEL NC16-seeria: NC16-25G10L | NC16-35G10L | NC16-50G10L
|
Sundsulatuse aktiveerimineCompulsory defrosting function:
Külmaaine kokkukogumineRefrigerant recovery function (applicable for movement or maintenance):
|
| ||||
NORDCEL NA18-Seeria: NA18-25G10L | NA18-35G10L | NA18-50G10L | NA18-70g10l
|
8 °C küttefunktsiooni käivitamiseks vajutage kütterežiimis olles samaaegselt nuppe TEMP ja CLOCK.
Puldi ekraanile kuvatakse sümbol ja valitud temperatuur 8 °C. Funktsioonist väljumiseks korrake protseduur
| ||||||||||||||||||||
NORDCEL NH16 seeria: nh16-25g10l | nh16-35g10l | nh16-50g10l | nh16-70g10l
|
8 °C küttefunktsiooni käivitamiseks vajutage kütterežiimis olles samaaegselt nuppe TEMP ja CLOCK.
Puldi ekraanile kuvatakse sümbol ja valitud temperatuur 8 °C. Funktsioonist väljumiseks korrake protseduur | |||||||||||||||||||||||||
NORDCEL NL18-seeria: nl18-25dcl | nl18-35dcl | nl18-50dcl | nl18-70dcl
|
| ||||||||
NORDCEL NV14-seeria: nv14-25dcl | NV14-35DCL | NV14-50DCL | nv14-70dcl
|
|
Veakoodide tabel välisosa kaane all
| ||||
nORDCEL nco16-seeria: ncoe16-25DCL | ncoe16-35dcl | ncoe16-50dcl | ncoe16-70dcl
| |||
nORDCEL õhk-vesi: NGRS-S3.5pdG
| |||
Wifi seadistamine: ewpe wifi sMArt
WIFI seadistamine
Lisainfo:
Küsimus: Mida teha, kui üle mobiilse interneti või mõnest teisest WiFi levialast ligipääs ebaõnnestub?
Vastus: Põhjuseks või olla, et Teie kodune WiFi ruuter on blokeerinud ühenduse välise teenusserveriga.
Soovitame kontrollida koduse wifi ruuteri tulemüüri seadistusi: lubada välisühendus läbi portide 6000: 6002: 16384: või avada pordid välisele aadressile 138.91.51.153. Vajadusel paluge selleks abi oma internetiteenuse osutajalt.
Küsimus: Mida teha, kui üle mobiilse interneti või mõnest teisest WiFi levialast ligipääs ebaõnnestub?
Vastus: Põhjuseks või olla, et Teie kodune WiFi ruuter on blokeerinud ühenduse välise teenusserveriga.
Soovitame kontrollida koduse wifi ruuteri tulemüüri seadistusi: lubada välisühendus läbi portide 6000: 6002: 16384: või avada pordid välisele aadressile 138.91.51.153. Vajadusel paluge selleks abi oma internetiteenuse osutajalt.
nordcel mOBIILNE KONDITIONEER: nsp19-12a3
| |||||
nORDCEL õHUKUIVATID: ngdn12aj | ngdn24aq | NGDN24BE
|
| ||||||
nordcel luna: NMS9A-09hHRDN1-QC2
| |||
NORDCEL LAEKASSETT: NGUHD
|
| |||
MuudE SEADMEte Juhendid:
gREE mULTI inverterID: fREE-mATCH r32
| |||
nordcel lAEKASSETID: nguhd
Gree seadmete veateated:
|
E1: Refrigerant system high pressure protection
E2: Anti-freezing protection E4: Compressor exhaust high temperature protection E5: AC over-current protection E6: Communication failure between indoor unit and outdoor unit E8: Anti-high temperature protection H1: The unit has entered defrost mode. This occurs when the control sensor of the outdoor heat exchanger activates and switches off heat injection to the indoor unit. Heat is diverted to the outdoor unit to defrost it. This error code can resolve itself if the defrost mode works correctly. You can inspect the outdoor unit to see if the process is working. If not, your unit may have a problem with the control sensor or heat exchanger, requiring an experienced technician. - The fault code is deduced from the number of times the green LED flashes, blocking unit operation H5: This error indicates that the intelligent power module has entered protection mode. Protection mode controls under-voltage and over-voltage issues, as well as over-temperature and short circuit issues. Your unit will need service to resolve this issue. Video H5 error H6: No feedback of indoor fan motor C5: Jumper cap malfunction protection F0: Refrigerant Leakage Protection F1: Indoor ambient sensor open or short circuit F2: Indoor tube sensor open or short circuit F3: Outdoor ambient sensor open or short circuit F4: Outdoor tube sensor open or short circuit F5: Exhaust sensor open or short circuit F6: Over load limit / drop frequency F8: Over current limit / drop frequency F9: High exhaust temperature limit / drop frequency PH: Over voltage protection for PN U5: AC current detect circuit malfunction U4: Compressor reverse protection P5: Over compressor phase current protection b5: Inlet tube sensor malfunction L3: Outdoor DC fan motor malfunction b7: Outlet tube sensor malfunction FC: Door malfunction FE: Compressor overload sensor malfunction H1: Defrosting H2: Static clearing dust protection H3: Compressor over load protection H4: System abnormal protection H5: IPM protection - https://youtu.be/IflQK42LUjw või https://youtu.be/XtnL9Tgh238?si=DlU1wNQzblNAxZwb HC: PFC protection H7: Compressor loss step protection H0: Heating anti-high temperature drop frequency Lc: Startup failure U2: Compressor protection against loss of phase U1: Compressor phase current detection circuit malfunction HE: Compressor demagnetization protection EE: Loading EEPROM malfunction P6: Communication failure between main board and driver board PU: Capacitor charge malfunction P7: IPM sensor circuit malfunction P8: IPM high temperature protection U3: PN voltage drop protection PL: Low PN voltage protection Pc: Current detect circuit malfunction or Current sensor malfunction Ld: Compressor loss of phase protection LE: Compressor locked rotary protection EU: IPM over temperature limit / drop frequency U7: 4-way valve reversal abnormal U8: Disconnection of the exhaust temperature sensor U9: AC power zero voltage detect error FA: Over tube temperature drop frequency FH: Anti-freezing limit / drop frequency oE: PFC module temperature protection/PFC module sensor malfunction C5: Malfunction of connector jumper: Check if the connector jumper contacts properly. If the PCB is to be replaced, please take off the old for the new PCB F1: Malfunction of indoor ambient temperature sensor:Check if indoor room temperature sensor is connected properly. F2: Malfunction of evaporator temperature sensor:Check if the evaporator temperature is connected properly. H1: Defrosting:It is normal H6: Indoor fan block:Check if terminal of the indoor motor is connected properly. Replace the fan motor or the indoor board if disabled. The wiring terminal between indoor evaporator temperature sensor and controller is loosened or poorly contacted;
Error Code F0 Refrigerant Leakage Protection Error Code F1 Indoor ambient sensor open or short circuit Error Code F2 Indoor tube sensor open or short circuit Error Code: F3 Malfunction Name: Outdoor ambient temperature sensor is open/ short-circuited A/C Status: The unit will stop operation as it reaches the temperature point. During cooling and drying operation, compressor stops and indoor fan operates; During heating operation, the complete unit stops operation. Possible Causes:
Malfunction Name: PG motor (indoor fan motor) does not operate A/C Status: Indoor fan, outdoor fan, compressor and electric heat tube stop operation. 2 minutes later, 4-way valve stops; horizontal louver stops at the current position. Possible Causes:
Error Code: C5 Malfunction Name: Malfunction protection of jumper cap A/C Status: Operation of remote controller or control panel is available, but the unit won’t act Possible Causes: There’s no jumper cap on the controller. Jumper cap is not inserted properly and tightly. Jumper cap is damaged. Controller is damaged. Error Code: U8 Malfunction Name: PG motor (indoor fan) circuit malfunction by zero cross detection A/C Status: Operation of remote controller or control panel is available, but the unit won’t act Possible Causes: Controller is damaged. Error Code: E2 Malfunction Name: Antifreezing protection A/C Status: During cooling and drying operation, compressor and outdoor fan stop while indoor fan operates. Possible Causes:
Malfunction Name: Low pressure protection of compressor A/C Status: The complete unit stops Possible Causes:
Malfunction Name: High pressure protection of system A/C Status: During cooling and drying operation, except indoor fan operates, all loads stop operation. During heating operation, the complete unit stops Possible Causes:
Malfunction Name: High discharge temperature protection of compressor A/C Status: During cooling and drying operation, compressor and outdoor fan stop while indoor fan operates. During heating operation, all loads stop Possible Causes: Please refer to the malfunction analysis (discharge protection, overload). Error Code: E5 Malfunction Name: Overcurrent protection A/C Status: During cooling and drying operation, compressor and outdoor fan stop while indoor fan operates. During heating operation, all loads stop Possible Causes:
Malfunction Name: Communication Malfunction A/C Status: During cooling operation, compressor stops while indoor fan motor operates. During heating operation, the complete unit stops Possible Causes: Refer to the corresponding malfunction analysis Error E7: This error appears when the outdoor unit and the indoor unit are set to different modes. When one unit is in heat mode and one unit is in cooling mode, your indoor display will show the E7 mode conflict error. To resolve this error code, inspect both the indoor and outdoor units. Switch the units to the desired mode, ensuring they match for correct functionality. Error Code: E8 Malfunction Name: High temperature resistant protection A/C Status: During cooling operation: compressor will stop while indoor fan will operate. During heating operation, the complete unit stops Possible Causes: Refer to the malfunction analysis (overload, high temperature resistant) Error Code: F4 Malfunction Name: Outdoor condenser temperature sensor is open/short circuited A/C Status: During cooling and drying operation, compressor stops while indoor fan will operate; During heating operation, the complete unit will stop operation. Possible Causes: Outdoor temperature sensor hasn’t been connected well or is damaged. Please check it by referring to the resistance table for temperature sensor) Error Code: F5 Malfunction Name: Outdoor discharge temperature sensor is open/short circuited A/C Status: During cooling and drying operation, compressor will sop after operating for about 3 mins, while indoor fan will operate; During heating operation, the complete unit will stop after operating for about 3 mins Possible Causes:
Malfunction Name: Limit/decrease frequency due to overload A/C Status: All loads operate normally, while operation frequency for compressor is decreased Possible Causes: Refer to the malfunction analysis (overload, high temperature resistant) Error Code: F8 Malfunction Name: Decrease frequency due to overcurrent A/C Status: All loads operate normally, while operation frequency for compressor is decreased Possible Causes: The input supply voltage is too low; System pressure is too high and overload Error Code: F9 Malfunction Name: Decrease frequency due to high air discharge A/C Status: All loads operate normally, while operation frequency for compressor is decreased Possible Causes:
Malfunction Name: Voltage for DC bus-bar is too high A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation. Possible Causes:
Malfunction Name: Malfunction of complete unit’s current detection A/C Status: During cooling and drying operation, the compressor will stop while indoor fan will operate; During heating operating, the complete unit will stop operation. Possible Causes: There’s circuit malfunction on outdoor unit’s control panel AP1, please replace the outdoor unit’s control panel AP1. Error Code: P5 Malfunction Name: Overcurrent protection of phase current for compressor A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation Possible Causes: Refer to the malfunction analysis (IPM protection, loss of synchronism protection and overcurrent protection of phase current for compressor. Error Code: H1 Malfunction Name: Defrosting A/C Status: Defrosting will occur in heating mode. Compressor will operate while indoor fan will stop operation. Possible Causes: It’s the normal state Error Code: H2 Malfunction Name: Static dedusting protection Error Code: H3 Malfunction Name: Overload protection for compressor A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation Possible Causes:
Malfunction Name: System is abnormal A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation. Possible Causes: Refer to the malfunction analysis (overload, high temperature resistant) Error Code: H5 - https://youtu.be/IflQK42LUjw Malfunction Name: IPM protection A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation. Possible Causes: Refer to the malfunction analysis (IPM protection, loss of synchronism protection and overcurrent protection of phase current for compressor. Error Code: HC Malfunction Name: PFC protection A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation. Possible Causes: Refer to the malfunction analysis Error Code: H7 Malfunction Name: Desynchronizing of compressor A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation. Possible Causes: Refer to the malfunction analysis (IPM protection, loss of synchronism protection and overcurrent protection of phase current for compressor. Error Code: H0 Malfunction Name: Decrease frequency due to high temperature resistant during heating operation A/C Status: All loads operate normally, while operation frequency for compressor is decreased Possible Causes: Refer to the malfunction analysis (overload, high temperature resistant) Error Code: Lc Malfunction Name: Failure start-up A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation Possible Causes: Refer to the malfunction analysis Error Code: U1 Malfunction Name: Malfunction of phase current detection circuit for compressor A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop Possible Causes: Replace outdoor control panel AP1 Error Code: EE Malfunction Name: EEPROM malfunction A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop Possible Causes: Replace outdoor control panel AP1 Error Code: PU Malfunction Name: Charging malfunction of capacitor A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop Possible Causes: Refer to the part three—charging malfunction analysis of capacitor Error Code: P7 Malfunction Name: Malfunction of module temperature sensor circuit A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop Possible Causes: Replace outdoor control panel AP1 Error Code: P8 Malfunction Name: Module high temperature protection A/C Status: During cooling operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop Possible Causes: After the complete unit is de-energized for 20mins, check whether the thermal grease on IPM Module of outdoor control panel AP1 is sufficient and whether the radiator is inserted tightly. If it’s no use, please replace control panel AP1. Error Code: U3 Malfunction Name: Malfunction of voltage dropping for DC bus-bar A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop Possible Causes: Supply voltage is unstable Error Code: PL Malfunction Name: Voltage of DC bus-bar is too low A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop Possible Causes:
Malfunction Name: Limit/decrease frequency due to high temperature of module A/C Status: All loads operate normally, while operation frequency for compressor is decreased Possible Causes: Discharging after the complete unit is de-energized for 20mins, check whether the thermal grease on IPM Module of outdoor control panel AP1 is sufficient and whether the radiator is inserted tightly. If it’s no use, please replace control panel AP1. Error Code: U7 Malfunction Name: The four-way valve is abnormal A/C Status: If this malfunction occurs during heating operation, the complete unit will stop operation Possible Causes:
Malfunction Name: Zero- crossing malfunction of outdoor unit A/C Status: During cooling operation, compressor will stop while indoor fan will operate; during heating, the complete unit will stop operation. Possible Causes: Replace outdoor control panel AP1 Error Code: FH Malfunction Name: Limit/decrease frequency due to antifreezing A/C Status: All loads operate normally, while operation frequency for compressor is decreased Possible Causes: Poor air-return in indoor unit or fan speed is too low Laekassetide veateated: Cassette AC Error Codes: In case of malfunction (such as bad smell), turn off the power immediately and contact the service center. Do not repair the air conditioner by yourself. Incorrect repairs may cause fire. Please contact the service center. The appliance should not be used by children without supervision. Once a failure occurs with the indoor unit in operation, the green unit LED flashes at intervals of 0.5 seconds. The fault code is deduced from the number of times the green LED flashes, blocking unit operation. Between one flash cycle and the next one, a pause of 5 seconds elapses. E1 High Pressure Protection. If outdoor unit detects the high pressure switch iscut off for 3-sec successively, high pressure protection will occur.All the loads (except the 4-way valve in heating mode) will be switched off. In thiscase, all the buttons and remote control signals except ON/OFF button will be disabled and system won't be recovered automatically. Switch off the unit or re-energize the unit after cutting off power to eliminate this protection. E2 Indoor Coil Freeze Protection. If indoor unit detects the evaporator temperature is lower than protective temperate value after the unit has been running for a period of time undercooling or dry mode, the unit will report this fault, in which case the compressor and outdoor fan motor will be stopped. The unit will not run until evaporator temperature is higher than the protective temp. value and the compressor is stopped for 3-min. E4 Compressor High Discharge Temperature Protection. f outdoor unit detects the discharge temperature is higher than protective temperature value, the unit will report high discharge temperature protection. If the protection occurs over 6 times, the unitcannot be recovered automatically. Switch off the unit or re-energize the unit aftercutting off power to reset this protection. E6 Communication Malfunction. If the outdoor unit does not receive data from indoor unit, communication malfunction will be reported. If there is communication abnormality between display board and indoor unit,communication malfunction will be reported. E8 Low Indoor Airflow. If the indoor unit does not receive signal from indoor fan motor for 30-secsuccessively when the fan motor is operating, indoor fan motor malfunction will be reported. In thiscase, the unitcan automatically resume operation after stopping. If the malfunction occurs 6 times within one hour, the unitcannot be recovered automatically. Switch off the unit or re-energize the unit after cutting off power to eliminate this malfunction. E9 Condensate Overflow Protection. If indoor unit detects the condensate overflow switch warning for 8-secsuccessively, the system will entercondensate overflow protection.The unit will shut off and will not recover automatically. Switch unit off and then switch it on to eliminate this malfunction. F0 Indoor Ambient Temperature Sensor at ReturnAir Inlet Malfunction. If indoor unit detects the indoor ambient temperature sensor is open circuit or shortcircuit for 5-secsuccessively, indoor ambient temp. sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. If indoor ambient temperature sensor malfunction occurs in fan mode, only the error code is displayed and the indoor unit will operate normally. F1 Indoor Evaporator Coil Temperature Sensor Malfunction. If indoor unit detects the evaporator temperature sensor is open circuit or shortcircuit for 5-secsuccessively, evaporator temperature sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. If evaporator temperature sensor malfunction occurs in fan mode, only the error code is displayed and the indoor unit will operate normally. F2 Indoor Condenser Coil Temperature Sensor Malfunction. If outdoor unit detects the condensercoil temperature sensor open circuit or shortcircuit for 5-secsuccessively,condensercoil temperature sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. Ifcondenser temperature sensor malfunction occurs in fan mode, only the error code is displayed and the indoor unit will operate normally. F3 Outdoor Ambient Temperature Sensor Malfunction. If outdoor unit detects the outdoor ambient temperature sensor open circuit or shortcircuit for 5-secsuccessively, outdoor ambient temperature sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. If outdoor ambient temperature sensor malfunction occurs in fan mode, only the errorcode is displayed and the indoor unit will operate normally. F4 Compressor Discharge Temperature Sensor Malfunction. If outdoor unit detects the compressor discharge temperature sensor is open circuit or shortcircuit for 5-secsuccessively after the compressor has been operating for 3-min, outdoor discharge temperature sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. F5 Wired Controller Temp. Sensor Malfunction. If the wired Tether Controller detects open circuit or shortcircuit of its temperature sensor for 5-secsuccessively,wired controller temperature sensor malfunction will be reported. H1 Defrost Mode. System is defrosting outdoorcoil. H3 Compressor Overload Protection. If outdoor unit detects the compressor overload switch open within 3-sec successively, the unit will reportcompressor overload protection. If the fault occurs successively 3 times, the unit will not recover automatically. Switch off the unit or re-energize the unit to eliminate this protection. H4 Overload Protection. If indoor unit detects the evaporatorcoil temperature is higher than protective temp. value, the unit will report overload protection. The unit will restart operation after evaporator temperature is lower than the protective temp. value and the compressor is stopped for 3-minutes. If the protection occurs over 6 times, the unit will not recover automatically. Switch off the unit or re-energize the unit to eliminate this protection. H6 Outdoor Fan Motor Malfunction. If outdoor unit does not receive feedback signal from outdoor fan motor for 30-secsuccessively when the fan motor is operating, an outdoor fan motor malfunction will be reported. In thiscase, the unit can automatically resume operation after stopping. If the malfunction occurs 6 times within one hour, the unit will not recover automatically. Switch off the unit or re-energize the unit to eliminate this malfunction. U7 Reversing or 4-wayValve Malfunction. After the compressor starts operation in heating mode, if the outdoor unit detects the difference between evaporator temperature and indoor ambient temperature is lower than the protective value for 10-min successively, ReversingValve Malfunction will be reported and the outdoor unit will stop operation. If the malfunction occurs 3 times, the unit will not recover automatically. Switch off the unit or re-energize the unit to eliminate this malfunction. Veel võimalikke veateateid erinevatel seadmetel: Error Codes: E1: High pressure protection of system E2: Antifreezing protection F0: In defect of refrigerant E4: High discharge temperature protection of compressor E5: Overcurrent protection E6: Communication Malfunction E8: High temperature resistant protection EE: EEPROM malfunction EU: Limit/ decrease frequency due to high temperature of module C5: Malfunction protection of jumper cap Remote Control Fo: Gathering refrigerant-Nominal cooling mode F1: Indoor ambient temperature sensor is open/short circuited F2: Indoor evaporator temperature sensor is open/short circuited F3: Outdoor ambient temperature sensor is open/short circuited F4: Outdoor condenser temperature sensor is open/short circuited F5: Outdoor discharge temperature sensor is open/short circuited F6: Limit/ decrease frequency due to overload F8: Decrease frequency due to overcurrent F9: Decrease frequency due to high air discharge FH: Limit/ decrease frequency due to antifreezing PH: Voltage for DC bus-bar is too high PL: Voltage of DC bus-bar is too low P0: Compressor Min frequence in test state P1: Compressor rated frequence in test state P2: Compressor maximum frequence in test state P3: Compressor intermediate frequence in test state P5: Overcurrent protection of phase current for compressor PU: Charging malfunction of capacitor P7: Malfunction of module temperature sensor circuit P8: Module high temperature protection H0: Decrease frequency due to high temperature resistant during heating operation H2: Static dedusting protection H3: Overload protection for compressor H4: System is abnormal H5: IPM protection H5: Module temperature is too high H6: Internal motor (fan motor) do not operate H7: Desynchronizing of compressor HC: PFC protection L3: Outdoor DC fan motor malfunction L9: power protection LP: Indoor unit and outdoor unit doesn’t match LC: Failure startup U1: Malfunction of phase current detection circuit for compressor U3: Malfunction of voltage dropping for DC bus-bar U5: Malfunction of complete units current detection U7: The four-way valve is abnormal U9: Zerocrossing malfunction of outdoor unit Gree Ductless Heat Pump Error Codes Models: GWH09KF-A3DNB1A / GWH12KF-A3DNB1A/ GWH09KF-D3DNB1C/ GWH12KF-D3DNB1C/ GWH18KG-D3DNB1C/ GWH24KG-D3DNB1A Error Codes / Possible Causes C5 Indoor Configuration Jumper/Missing Configuration Jumper on Indoor Control Board LP Indoor/Outdoor Mismatch/Indoor and Outdoor Units Do Not Match E5 High Current Protection/Power Supply is not Stable and Voltage Range is too Large E6 Communication Error/Mis-wired or Communication Failure F1 Indoor Air Temp. Thermistor/Bad Connection, or Indoor Air Sensor Failure F2 Indoor Coil Temp. Thermistor/Bad Connection, or Indoor Coil Sensor Failure F3 Outdoor Air Temp. Thermistor/Bad Connection, or Outdoor Ambient Sensor Failure F4 Outdoor Coil Temp. Thermistor/Bad Connection, or Outdoor Coil Sensor Failure F5 Compressor Discharge Temp. Thermistor/Bad Connection, or Discharge Sensor Failure H3 Compressor Overload Protection/Low Refrigerant Charge H5 IPM Module Protection/IPM Module Temperature Too High H6 Indoor Fan Malfunction/Indoor Fan Stopped or Running too Slow H7 Compressor Synchronism/High Pressure, Low Voltage, or Bad Connections U7 4-Way Valve Malfunction/Bad Connection, Solenoid Failure, or Valve Malfunction. Mobiilsete seadmete veateated: Portable Air Conditioner Error Codes In some cases, problems can be solved easily without the help from the Customer Service department just by checking the following. If the problem still persists after you check the following, then contact the Customer Service department. Error Code : H8 Problem: Chassis is full of water. Solution: 1. Pour out the water inside chassis. 2. If “H8” still exists, please contact Customer Service. Error Code : F1 Problem: Malfunction of temperature sensor. Solution: Please contact Customer Service Error Code : F2 Problem: Malfunction of evaporator temperature sensor. Solution: Please contact Customer Service Error Code : F0 Problem:
Problem: Overload protection for compressor-Overload malfunction Solution:
Problem: Overload malfunction Solution:
Problem: Outdoor tube temperature sensor is open/short-circuited. Solution: Please contact Customer Service Error Code : E5 Problem: Overcurrent protection Solution:
Air Conditioner Troubleshooting *Problem Water leaking from the indoor unit into the room. Cause/Solution Cause: While it is normal for the system to generate condensate water in coolingmode, it is designed to drain this water via a condensate drain system to a safe location. Solution: If water is leaking into the room, it may indicate one of the following
Wireless remote controller does not work. Cause/Solution Cause: There are a number of possible reasons Solution: Check the following:
|
Surveproov ja vaakumeerimine
Soojuspumpadel on tehases testitud rõhku ja lekkimist, kuid toodetevahelisi toruühendusi tuleb pärast paigaldamist kontrollida. Tähelepanu! Toodete vahelistel toruühendustel tuleb pärast paigaldust testida rõhku ja lekkimist vastavalt kehtivatele määrustele. Mitte mingitel tingimustel ei tohi süsteemi survestamiseks ega läbipesuks kasutada muud tüüpi elementi kui lämmastikku. |
Air Conditioner Error Codes
CODES OF ERRORS OF GREE AIR CONDITIONERS
Error code display Indicator Flashing indicators on the indoor unit Errors in operation or tripping of protection
E1 Operation indicator Flashes once every 3 seconds Compressor protection against high pressure
E2 Flashing 2 times every 3 seconds Protection against freezing of indoor unit
E3 Flashing 3 times every 3 seconds Compressor protection against low pressure
E4 Flashing 4 times every 3 seconds High temperature protection on the compressor discharge pipe
E5 Flashing 5 times every 3 seconds Protecting the compressor or system from overloads
E6 Flashes 6 times every 3 seconds. Connection fault (commutation). Absence of supply and signal cables (absence of phase)
E7 Flashing 7 times every 3 seconds Contrast of the set mode
E8 Blinks 8 times every 3 seconds. Evaporator protection against overheating. The motor protection of the indoor unit has tripped.
E9 Flashing 9 times every 3 seconds Cold air supply protection in heating mode
E0 Flashing 10 times every 3 seconds Protection of the frequency controller at low starting voltage
H6 Flashing 11 times every 3 seconds No feedback signal from the fan motor of the indoor unit
F0 Temperature sensor fault
F1 Cold running indicator Flashes once every 3 seconds Temperature sensor fault on the evaporator
F2 Flashes 2 times every 3 seconds Condenser temperature sensor fault
F3 Blinks 3 times every 3 seconds Ambient air sensor fault in outdoor unit
F4 Flashing 4 times every 3 seconds Temperature pump fault
F5 Flashing 5 times every 3 seconds Malfunction of the sensor on the discharge pipe of the compressor
F6 Flashing 6 times every 3 seconds Condenser overheating at low speed in cooling mode (Inverter)
F7 Flashing 7 times every 3 seconds Protecting against oil carrying from the compressor (Inverter)
F8 Blinks 8 times every 3 seconds Compressor or system protection against overload at low speed (Inverter)
F9 Flashing 9 times every 3 seconds Compressor protection at high discharge and low speed (Inverter)
FF Phase monitor malfunction, no power supply to one phase
H1 Heat-on indicator Flashing once every 3 seconds Defrosting
H2 Flashing 2 times every 3 seconds Protection of electrostatic filter
H3 Flashing 3 times every 3 seconds Protecting the compressor against overheating
H4 Flashes 4 times every 3 seconds System malfunction
H5 Blinks 5 times every 3 seconds IPM block protection
H7 Flashes 6 times every 3 seconds Compressor fault (DC Inverter)
H8 Flashing 7 times every 3 seconds Drainage overflow protection
H9 Flashes 8 times every 3 seconds Faulty electric heater
H0 Flashing 9 times every 3 seconds Evaporator protection against overheating (Inverter)
FA Protection of evaporator or condenser against overheating at low speed (Inverter)
FH Evaporator frost protection (Inverter)
Tööstusseademete võimalikud veateated:
Air conditioners of semi-industrial, industrial use, - error codes.
Error code = E1
Compressor, pressure surge (sound signal).
Error code = E2
Defective coil
Error code = E3
The compressor of the air conditioner was activated under low pressure (sound signal)
Error code = F0
Defective room temperature sensor.
Error code = F1
Wrong sensor resistance.
Error code = F2
The temperature sensor of the outdoor unit of the air conditioner was activated.
Error code = F3
The temperature sensor circuit is open.
GREE Split Air Conditioner Error Code ...
The cause of the malfunction, - the refrigerant system is a high degree of protection, - pressure.
Code = E1
LED start of the air conditioner = the Gree LED flashes 1 time.
Indicator, - cooling =
Heating indicator =
The cause of Gree faults is frost protection.
Code = E2
LED start the air conditioner = LED flashes 2 times.
Indicator, - cooling =
Heating indicator =
The cause of the malfunction is the high-temperature exhaust exhaust compressor.
Code = E4
LED start the air conditioner = blink 4 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - AC overload protection
Code = E5
LED start the air conditioner = LED flashes 5 times
Indicator, - cooling =
Heating indicator =
The cause of the malfunction is the communication failure between the indoor unit of the air conditioner and the outdoor unit of the split system.
Code = E6
LED starts the air conditioner Gree = flashes 6 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Anti-high temperature protection
Code = E8
LED start the air conditioner = blink 8 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - There is no feedback from the internal fan motor
Code = H6
LED start the air conditioner = flashes 11 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Jumper header defective
Code = C5
LED start the air conditioner = flashes 15 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Closed ambient sensor open, no contact or short circuit
Code = F1
Indicator, - cooling = LED flashing 1 time
Heating indicator =
Name malfunction or sensor failure = Indoor tube open, no contact or short circuit
Code = F2
LED start the air conditioning =
Indicator, - cooling = LED flashing 2 times
Heating indicator =
The cause of the malfunction, - the outdoor ambient sensor is open, there is no contact or short circuit
Code = F3
LED start the air conditioning =
Indicator, - cooling = LED flashing 3 times
Heating indicator =
Cause of malfunction, - External tube sensor open, no contact or short circuit
Code = F4
LED start the air conditioning =
Indicator, - cooling = blinking 4 times
Heating indicator =
Name = Fault or malfunction of the exhaust sensor open, no contact or short circuit
Code = F5
LED start the air conditioning =
Indicator, - cooling = LED flashing 5 times
Heating indicator =
Cause of failure, - Overload / frequency reduction
Code = F6
LED start the air conditioning =
Indicator, - cooling = Blink 6 times
Heating indicator =
Cause of malfunction, - For limiting the current / output frequency
Code = F8
LED start the air conditioning =
Indicator, - cooling = blinking 8 times
Heating indicator =
Cause of malfunction, - High exhaust gas temperature limit / frequency reduction
Code = F9
LED start the air conditioning =
Indicator, - cooling flash = 9 times
Heating indicator =
Fault cause, - Overvoltage protection for Roux
Code = PH
LED start the air conditioning =
Indicator, - cooling = flashing 11 times
Heating indicator =
The cause of the malfunction is the alternating detection current of the defective circuit
Code = U5
LED start the air conditioning =
Indicator, - cooling = flashing 13 times
Heating indicator =
Cause of malfunction, - Compressor reverse protection
Code = U4
LED start the air conditioning =
Indicator, - cooling = flashing 14 times
Heating indicator =
The cause of the malfunction, - Behind the phase current compressor
Code = P5
LED start the air conditioning =
Indicator, - cooling = flashing 15 times
Heating indicator =
The cause of the malfunction is the entrance of the malfucntion with a probe tube
Code = b5
LED start the air conditioning =
Indicator, - cooling = flashing 19 times
Heating indicator =
Cause of malfunction, - The open DC fan motor is defective.
Code = L3
LED start the air conditioning =
Indicator, - cooling = flashing 21 times
Heating indicator =
Cause of malfunction, - Output malfunction or tube sensor failure
Code = b7
LED start the air conditioning =
Indicator, - cooling = blinking 22 times
Heating indicator =
Cause of malfunction, - The overload sensor is faulty.
Code = FE
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Defrost
Code = H1
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = LED flashes 1 time
The cause of the malfunction is static dust protection
Code = H2
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = LED flashes 2 times
Cause of malfunction, - Overload protection
Code = H3
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = LED flashes 3 times
Cause of malfunction, - System abnormal protection
Code = H4
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 4 times
The cause of the malfunction, - IPM protection
Code = H5
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = LED flashes 5 times
Cause of malfunction, - PFC protection
Code = HC
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = blinks 6 times
Cause of malfunction, - Step protection compressor
Code = H7
LED start the air conditioning =
Indicator, - cooling =
Heating indicator flash = 7 times
Cause of malfunction, - Heating against high-frequency drop in temperature
Code = HO
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 10 times
Cause of failure, - Run failure
Code = Lc
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 11 times
Cause of malfunction, - Phase failure protection compressor
Code = U2
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 12 times
The cause of the malfunction, - The phase current compressor is defective. Detection circuits
Code = U1
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = blinks 13 times
Cause of malfunction, - Demagnetization compressor protection
Code = HE
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 14 times
Cause of malfunction, - EEPROM boot failed.
Code = EE
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 15 times
The cause of the malfunction is a communication failure between the motherboard and the board driver
Code = P6
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 16 times
Cause of malfunction, - Charge failure capacitor
Code = PU
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 17 times
The cause of the malfunction, - the ИПМ of the sensor circuit is defective.
Code = P7
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 18 times
The cause of the malfunction is the high-temperature protection IPM
Code = P8
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = blinks 19 times
Cause of malfunction, - PN voltage drop protection
Code = U3
LED start the air conditioning =
Indicator, - cooling = flashing 20 times
Heating indicator =
Cause of malfunction, - low voltage protection PN
Code = PL
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 21 times
Cause of malfunction, - Current detection circuit is defective. Or fault or sensor fault current
Code = Pc
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of failure, - Phase failure protection compressor
Code = Ld
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Compressor or blocked rotary protection
Code = LE
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - ИПМ more than temperature limit / frequency reduction
Code = EU
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
The cause of the malfunction, - the 4-way turn valve is abnormal
Code = U7
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - switch off the exhaust gas temperature sensor
Code = U8
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - AC zero fault detection voltage
Code = U9
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Over the tube temperature drop frequency
Code = FA
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Anti-freeze limit / decrease frequency
Code = FH
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
CODES OF ERRORS OF GREE AIR CONDITIONERS
Error code display Indicator Flashing indicators on the indoor unit Errors in operation or tripping of protection
E1 Operation indicator Flashes once every 3 seconds Compressor protection against high pressure
E2 Flashing 2 times every 3 seconds Protection against freezing of indoor unit
E3 Flashing 3 times every 3 seconds Compressor protection against low pressure
E4 Flashing 4 times every 3 seconds High temperature protection on the compressor discharge pipe
E5 Flashing 5 times every 3 seconds Protecting the compressor or system from overloads
E6 Flashes 6 times every 3 seconds. Connection fault (commutation). Absence of supply and signal cables (absence of phase)
E7 Flashing 7 times every 3 seconds Contrast of the set mode
E8 Blinks 8 times every 3 seconds. Evaporator protection against overheating. The motor protection of the indoor unit has tripped.
E9 Flashing 9 times every 3 seconds Cold air supply protection in heating mode
E0 Flashing 10 times every 3 seconds Protection of the frequency controller at low starting voltage
H6 Flashing 11 times every 3 seconds No feedback signal from the fan motor of the indoor unit
F0 Temperature sensor fault
F1 Cold running indicator Flashes once every 3 seconds Temperature sensor fault on the evaporator
F2 Flashes 2 times every 3 seconds Condenser temperature sensor fault
F3 Blinks 3 times every 3 seconds Ambient air sensor fault in outdoor unit
F4 Flashing 4 times every 3 seconds Temperature pump fault
F5 Flashing 5 times every 3 seconds Malfunction of the sensor on the discharge pipe of the compressor
F6 Flashing 6 times every 3 seconds Condenser overheating at low speed in cooling mode (Inverter)
F7 Flashing 7 times every 3 seconds Protecting against oil carrying from the compressor (Inverter)
F8 Blinks 8 times every 3 seconds Compressor or system protection against overload at low speed (Inverter)
F9 Flashing 9 times every 3 seconds Compressor protection at high discharge and low speed (Inverter)
FF Phase monitor malfunction, no power supply to one phase
H1 Heat-on indicator Flashing once every 3 seconds Defrosting
H2 Flashing 2 times every 3 seconds Protection of electrostatic filter
H3 Flashing 3 times every 3 seconds Protecting the compressor against overheating
H4 Flashes 4 times every 3 seconds System malfunction
H5 Blinks 5 times every 3 seconds IPM block protection
H7 Flashes 6 times every 3 seconds Compressor fault (DC Inverter)
H8 Flashing 7 times every 3 seconds Drainage overflow protection
H9 Flashes 8 times every 3 seconds Faulty electric heater
H0 Flashing 9 times every 3 seconds Evaporator protection against overheating (Inverter)
FA Protection of evaporator or condenser against overheating at low speed (Inverter)
FH Evaporator frost protection (Inverter)
Tööstusseademete võimalikud veateated:
Air conditioners of semi-industrial, industrial use, - error codes.
Error code = E1
Compressor, pressure surge (sound signal).
Error code = E2
Defective coil
Error code = E3
The compressor of the air conditioner was activated under low pressure (sound signal)
Error code = F0
Defective room temperature sensor.
Error code = F1
Wrong sensor resistance.
Error code = F2
The temperature sensor of the outdoor unit of the air conditioner was activated.
Error code = F3
The temperature sensor circuit is open.
GREE Split Air Conditioner Error Code ...
The cause of the malfunction, - the refrigerant system is a high degree of protection, - pressure.
Code = E1
LED start of the air conditioner = the Gree LED flashes 1 time.
Indicator, - cooling =
Heating indicator =
The cause of Gree faults is frost protection.
Code = E2
LED start the air conditioner = LED flashes 2 times.
Indicator, - cooling =
Heating indicator =
The cause of the malfunction is the high-temperature exhaust exhaust compressor.
Code = E4
LED start the air conditioner = blink 4 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - AC overload protection
Code = E5
LED start the air conditioner = LED flashes 5 times
Indicator, - cooling =
Heating indicator =
The cause of the malfunction is the communication failure between the indoor unit of the air conditioner and the outdoor unit of the split system.
Code = E6
LED starts the air conditioner Gree = flashes 6 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Anti-high temperature protection
Code = E8
LED start the air conditioner = blink 8 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - There is no feedback from the internal fan motor
Code = H6
LED start the air conditioner = flashes 11 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Jumper header defective
Code = C5
LED start the air conditioner = flashes 15 times
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Closed ambient sensor open, no contact or short circuit
Code = F1
Indicator, - cooling = LED flashing 1 time
Heating indicator =
Name malfunction or sensor failure = Indoor tube open, no contact or short circuit
Code = F2
LED start the air conditioning =
Indicator, - cooling = LED flashing 2 times
Heating indicator =
The cause of the malfunction, - the outdoor ambient sensor is open, there is no contact or short circuit
Code = F3
LED start the air conditioning =
Indicator, - cooling = LED flashing 3 times
Heating indicator =
Cause of malfunction, - External tube sensor open, no contact or short circuit
Code = F4
LED start the air conditioning =
Indicator, - cooling = blinking 4 times
Heating indicator =
Name = Fault or malfunction of the exhaust sensor open, no contact or short circuit
Code = F5
LED start the air conditioning =
Indicator, - cooling = LED flashing 5 times
Heating indicator =
Cause of failure, - Overload / frequency reduction
Code = F6
LED start the air conditioning =
Indicator, - cooling = Blink 6 times
Heating indicator =
Cause of malfunction, - For limiting the current / output frequency
Code = F8
LED start the air conditioning =
Indicator, - cooling = blinking 8 times
Heating indicator =
Cause of malfunction, - High exhaust gas temperature limit / frequency reduction
Code = F9
LED start the air conditioning =
Indicator, - cooling flash = 9 times
Heating indicator =
Fault cause, - Overvoltage protection for Roux
Code = PH
LED start the air conditioning =
Indicator, - cooling = flashing 11 times
Heating indicator =
The cause of the malfunction is the alternating detection current of the defective circuit
Code = U5
LED start the air conditioning =
Indicator, - cooling = flashing 13 times
Heating indicator =
Cause of malfunction, - Compressor reverse protection
Code = U4
LED start the air conditioning =
Indicator, - cooling = flashing 14 times
Heating indicator =
The cause of the malfunction, - Behind the phase current compressor
Code = P5
LED start the air conditioning =
Indicator, - cooling = flashing 15 times
Heating indicator =
The cause of the malfunction is the entrance of the malfucntion with a probe tube
Code = b5
LED start the air conditioning =
Indicator, - cooling = flashing 19 times
Heating indicator =
Cause of malfunction, - The open DC fan motor is defective.
Code = L3
LED start the air conditioning =
Indicator, - cooling = flashing 21 times
Heating indicator =
Cause of malfunction, - Output malfunction or tube sensor failure
Code = b7
LED start the air conditioning =
Indicator, - cooling = blinking 22 times
Heating indicator =
Cause of malfunction, - The overload sensor is faulty.
Code = FE
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Defrost
Code = H1
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = LED flashes 1 time
The cause of the malfunction is static dust protection
Code = H2
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = LED flashes 2 times
Cause of malfunction, - Overload protection
Code = H3
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = LED flashes 3 times
Cause of malfunction, - System abnormal protection
Code = H4
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 4 times
The cause of the malfunction, - IPM protection
Code = H5
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = LED flashes 5 times
Cause of malfunction, - PFC protection
Code = HC
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = blinks 6 times
Cause of malfunction, - Step protection compressor
Code = H7
LED start the air conditioning =
Indicator, - cooling =
Heating indicator flash = 7 times
Cause of malfunction, - Heating against high-frequency drop in temperature
Code = HO
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 10 times
Cause of failure, - Run failure
Code = Lc
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 11 times
Cause of malfunction, - Phase failure protection compressor
Code = U2
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 12 times
The cause of the malfunction, - The phase current compressor is defective. Detection circuits
Code = U1
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = blinks 13 times
Cause of malfunction, - Demagnetization compressor protection
Code = HE
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 14 times
Cause of malfunction, - EEPROM boot failed.
Code = EE
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 15 times
The cause of the malfunction is a communication failure between the motherboard and the board driver
Code = P6
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 16 times
Cause of malfunction, - Charge failure capacitor
Code = PU
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 17 times
The cause of the malfunction, - the ИПМ of the sensor circuit is defective.
Code = P7
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 18 times
The cause of the malfunction is the high-temperature protection IPM
Code = P8
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = blinks 19 times
Cause of malfunction, - PN voltage drop protection
Code = U3
LED start the air conditioning =
Indicator, - cooling = flashing 20 times
Heating indicator =
Cause of malfunction, - low voltage protection PN
Code = PL
LED start the air conditioning =
Indicator, - cooling =
Heating indicator = flashes 21 times
Cause of malfunction, - Current detection circuit is defective. Or fault or sensor fault current
Code = Pc
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of failure, - Phase failure protection compressor
Code = Ld
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Compressor or blocked rotary protection
Code = LE
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - ИПМ more than temperature limit / frequency reduction
Code = EU
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
The cause of the malfunction, - the 4-way turn valve is abnormal
Code = U7
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - switch off the exhaust gas temperature sensor
Code = U8
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - AC zero fault detection voltage
Code = U9
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Over the tube temperature drop frequency
Code = FA
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
Cause of malfunction, - Anti-freeze limit / decrease frequency
Code = FH
LED start the air conditioning =
Indicator, - cooling =
Heating indicator =
GREE VERSATI III
| Gree-Versati_III_split_user_manual.pdf |
Unico Evo 25 HP PVAN
| unico_paigaldusjuhend_piltidega.pdf |
| unico_pro_kasutusjuhend.pdf |
| unico_evo_wifi_juhend.pdf |
nibe SEADMETE info ja JUHENDID
nibe VEATEADETE (ALARM) KIRJELDUSED:
|
NIBE F-seeria veateadete kirjeldused / Alarm search for products NIBE
https://partner.nibe.eu/etc/Service/Alarms/
NIBE S-seeria veateadete kirjeldused / Alarm search for products NIBE S1155, S1255, VVM S320, SMO S40
https://partner.nibe.eu/etc/Service/alarm-search-s-series/
| ||||
NIBE seadmete paigaldamise PÕHIMÕTTESKEEMID:
vENTILATSIOONI seadmete JUHENDID:
bLAUBERG: eRGO | eXPERT | rOTO |
|
|
NB! Filter reset:
VENTO Expert A50-1 W / DUO A30-1 W To reset the filter timer, turn the DIP switch No. 8 on for not less than 3 seconds and then turn it of VENTO Expert A50-1 W / DUO A30-1 W To reset the filter timer set the third jumper to ON position and then revert it to OFF position. VENTO Expert A50-1 W V3 After replacement of the filters reset the timer using the mobile application or by pressing and holding the button on the Master ventilator indoor unit for 5 seconds until a signal sounds. | ||||||||||
|
| ||||
vallox: 096mv | 110mv | 145mv
| |||
õhkkardinad:
frico
| |||||||||||||||
sONNIGER
vts Wing ja Volcano
|
| ||||||||||||
Paigaldajal peab olema vastav sertifikaat, et töötada näiteks tavaliselt kasutatava külmutusagensiga R32 (difluorometaan) või vanamoodsa R410A (difluorometaani ja pentafluoroetaani seguga). Need külmutusagensid on välja töötatud laboris ja seetõttu nimetatakse neid sünteetilisteks külmutusagensideks.
Need kuuluvad fluorosüsivesinike koondnimetuse alla, mida sageli nimetatakse F-gaasideks või HFC-deks.
Need kuuluvad fluorosüsivesinike koondnimetuse alla, mida sageli nimetatakse F-gaasideks või HFC-deks.
